diff --git a/keyboards/wilba_tech/wt60_a/keymaps/via/rules.mk b/keyboards/wilba_tech/wt60_a/keymaps/via/rules.mk index 76a07d7a..8834bf0c 100644 --- a/keyboards/wilba_tech/wt60_a/keymaps/via/rules.mk +++ b/keyboards/wilba_tech/wt60_a/keymaps/via/rules.mk @@ -1,71 +1,2 @@ -# project specific files -SRC = drivers/issi/is31fl3736.c \ - drivers/avr/i2c_master.c \ - keyboards/wilba_tech/wt_mono_backlight.c \ - keyboards/wilba_tech/wt_main.c - -# MCU name -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section -BOOTLOADER = atmel-dfu - - -# Build Options -# change yes to no to disable -# -BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE = no # Mouse keys(+4700) -EXTRAKEY_ENABLE = yes # Audio control and System control(+450) -CONSOLE_ENABLE = no # Console for debug(+400) -COMMAND_ENABLE = no # Commands for debug and configuration -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend -# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -NKRO_ENABLE = yes # USB Nkey Rollover -BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality on B7 by default -MIDI_ENABLE = no # MIDI support (+2400 to 4200, depending on config) -UNICODE_ENABLE = no # Unicode -BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID -AUDIO_ENABLE = no # Audio output on port C6 -FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches - RAW_ENABLE = yes DYNAMIC_KEYMAP_ENABLE = yes \ No newline at end of file diff --git a/keyboards/wilba_tech/wt60_d/keymaps/via/rules.mk b/keyboards/wilba_tech/wt60_d/keymaps/via/rules.mk index f072c671..8834bf0c 100644 --- a/keyboards/wilba_tech/wt60_d/keymaps/via/rules.mk +++ b/keyboards/wilba_tech/wt60_d/keymaps/via/rules.mk @@ -1,68 +1,2 @@ -# project specific files -SRC = keyboards/wilba_tech/wt_main.c - -# MCU name -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section -BOOTLOADER = atmel-dfu - - -# Build Options -# change yes to no to disable -# -BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE = no # Mouse keys(+4700) -EXTRAKEY_ENABLE = yes # Audio control and System control(+450) -CONSOLE_ENABLE = no # Console for debug(+400) -COMMAND_ENABLE = no # Commands for debug and configuration -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend -# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -NKRO_ENABLE = yes # USB Nkey Rollover -BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality on B7 by default -MIDI_ENABLE = no # MIDI support (+2400 to 4200, depending on config) -UNICODE_ENABLE = no # Unicode -BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID -AUDIO_ENABLE = no # Audio output on port C6 -FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches - RAW_ENABLE = yes DYNAMIC_KEYMAP_ENABLE = yes \ No newline at end of file diff --git a/keyboards/wilba_tech/wt65_a/keymaps/via/rules.mk b/keyboards/wilba_tech/wt65_a/keymaps/via/rules.mk index 76a07d7a..8834bf0c 100644 --- a/keyboards/wilba_tech/wt65_a/keymaps/via/rules.mk +++ b/keyboards/wilba_tech/wt65_a/keymaps/via/rules.mk @@ -1,71 +1,2 @@ -# project specific files -SRC = drivers/issi/is31fl3736.c \ - drivers/avr/i2c_master.c \ - keyboards/wilba_tech/wt_mono_backlight.c \ - keyboards/wilba_tech/wt_main.c - -# MCU name -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section -BOOTLOADER = atmel-dfu - - -# Build Options -# change yes to no to disable -# -BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE = no # Mouse keys(+4700) -EXTRAKEY_ENABLE = yes # Audio control and System control(+450) -CONSOLE_ENABLE = no # Console for debug(+400) -COMMAND_ENABLE = no # Commands for debug and configuration -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend -# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -NKRO_ENABLE = yes # USB Nkey Rollover -BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality on B7 by default -MIDI_ENABLE = no # MIDI support (+2400 to 4200, depending on config) -UNICODE_ENABLE = no # Unicode -BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID -AUDIO_ENABLE = no # Audio output on port C6 -FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches - RAW_ENABLE = yes DYNAMIC_KEYMAP_ENABLE = yes \ No newline at end of file diff --git a/keyboards/wilba_tech/wt65_b/keymaps/via/rules.mk b/keyboards/wilba_tech/wt65_b/keymaps/via/rules.mk index 76a07d7a..8834bf0c 100644 --- a/keyboards/wilba_tech/wt65_b/keymaps/via/rules.mk +++ b/keyboards/wilba_tech/wt65_b/keymaps/via/rules.mk @@ -1,71 +1,2 @@ -# project specific files -SRC = drivers/issi/is31fl3736.c \ - drivers/avr/i2c_master.c \ - keyboards/wilba_tech/wt_mono_backlight.c \ - keyboards/wilba_tech/wt_main.c - -# MCU name -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section -BOOTLOADER = atmel-dfu - - -# Build Options -# change yes to no to disable -# -BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE = no # Mouse keys(+4700) -EXTRAKEY_ENABLE = yes # Audio control and System control(+450) -CONSOLE_ENABLE = no # Console for debug(+400) -COMMAND_ENABLE = no # Commands for debug and configuration -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend -# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -NKRO_ENABLE = yes # USB Nkey Rollover -BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality on B7 by default -MIDI_ENABLE = no # MIDI support (+2400 to 4200, depending on config) -UNICODE_ENABLE = no # Unicode -BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID -AUDIO_ENABLE = no # Audio output on port C6 -FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches - RAW_ENABLE = yes DYNAMIC_KEYMAP_ENABLE = yes \ No newline at end of file diff --git a/keyboards/wilba_tech/wt69_a/keymaps/via/rules.mk b/keyboards/wilba_tech/wt69_a/keymaps/via/rules.mk index f072c671..8834bf0c 100644 --- a/keyboards/wilba_tech/wt69_a/keymaps/via/rules.mk +++ b/keyboards/wilba_tech/wt69_a/keymaps/via/rules.mk @@ -1,68 +1,2 @@ -# project specific files -SRC = keyboards/wilba_tech/wt_main.c - -# MCU name -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section -BOOTLOADER = atmel-dfu - - -# Build Options -# change yes to no to disable -# -BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE = no # Mouse keys(+4700) -EXTRAKEY_ENABLE = yes # Audio control and System control(+450) -CONSOLE_ENABLE = no # Console for debug(+400) -COMMAND_ENABLE = no # Commands for debug and configuration -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend -# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -NKRO_ENABLE = yes # USB Nkey Rollover -BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality on B7 by default -MIDI_ENABLE = no # MIDI support (+2400 to 4200, depending on config) -UNICODE_ENABLE = no # Unicode -BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID -AUDIO_ENABLE = no # Audio output on port C6 -FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches - RAW_ENABLE = yes DYNAMIC_KEYMAP_ENABLE = yes \ No newline at end of file diff --git a/keyboards/wilba_tech/wt75_a/keymaps/via/rules.mk b/keyboards/wilba_tech/wt75_a/keymaps/via/rules.mk index 76a07d7a..8834bf0c 100644 --- a/keyboards/wilba_tech/wt75_a/keymaps/via/rules.mk +++ b/keyboards/wilba_tech/wt75_a/keymaps/via/rules.mk @@ -1,71 +1,2 @@ -# project specific files -SRC = drivers/issi/is31fl3736.c \ - drivers/avr/i2c_master.c \ - keyboards/wilba_tech/wt_mono_backlight.c \ - keyboards/wilba_tech/wt_main.c - -# MCU name -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section -BOOTLOADER = atmel-dfu - - -# Build Options -# change yes to no to disable -# -BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE = no # Mouse keys(+4700) -EXTRAKEY_ENABLE = yes # Audio control and System control(+450) -CONSOLE_ENABLE = no # Console for debug(+400) -COMMAND_ENABLE = no # Commands for debug and configuration -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend -# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -NKRO_ENABLE = yes # USB Nkey Rollover -BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality on B7 by default -MIDI_ENABLE = no # MIDI support (+2400 to 4200, depending on config) -UNICODE_ENABLE = no # Unicode -BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID -AUDIO_ENABLE = no # Audio output on port C6 -FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches - RAW_ENABLE = yes DYNAMIC_KEYMAP_ENABLE = yes \ No newline at end of file diff --git a/keyboards/wilba_tech/wt75_b/keymaps/via/rules.mk b/keyboards/wilba_tech/wt75_b/keymaps/via/rules.mk index 76a07d7a..8834bf0c 100644 --- a/keyboards/wilba_tech/wt75_b/keymaps/via/rules.mk +++ b/keyboards/wilba_tech/wt75_b/keymaps/via/rules.mk @@ -1,71 +1,2 @@ -# project specific files -SRC = drivers/issi/is31fl3736.c \ - drivers/avr/i2c_master.c \ - keyboards/wilba_tech/wt_mono_backlight.c \ - keyboards/wilba_tech/wt_main.c - -# MCU name -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section -BOOTLOADER = atmel-dfu - - -# Build Options -# change yes to no to disable -# -BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE = no # Mouse keys(+4700) -EXTRAKEY_ENABLE = yes # Audio control and System control(+450) -CONSOLE_ENABLE = no # Console for debug(+400) -COMMAND_ENABLE = no # Commands for debug and configuration -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend -# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -NKRO_ENABLE = yes # USB Nkey Rollover -BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality on B7 by default -MIDI_ENABLE = no # MIDI support (+2400 to 4200, depending on config) -UNICODE_ENABLE = no # Unicode -BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID -AUDIO_ENABLE = no # Audio output on port C6 -FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches - RAW_ENABLE = yes DYNAMIC_KEYMAP_ENABLE = yes \ No newline at end of file diff --git a/keyboards/wilba_tech/wt75_c/keymaps/via/keymap.c b/keyboards/wilba_tech/wt75_c/keymaps/via/keymap.c new file mode 100644 index 00000000..0eedd4cb --- /dev/null +++ b/keyboards/wilba_tech/wt75_c/keymaps/via/keymap.c @@ -0,0 +1,41 @@ +#include QMK_KEYBOARD_H + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + + // Default layer + [0] = LAYOUT_all( + KC_ESC, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_PSCR, + KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSPC, KC_BSPC, KC_DEL, + KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS, KC_PGUP, + KC_CAPS, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_ENT, KC_PGDN, + KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSFT, KC_UP, + KC_LCTL, KC_LGUI, KC_LALT, KC_SPC, KC_RALT, MO(1), KC_LEFT, KC_DOWN, KC_RGHT), + + // Fn1 Layer + [1] = LAYOUT_all( + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS), + + // Fn2 Layer + [2] = LAYOUT_all( + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS), + + // Fn3 Layer + [3] = LAYOUT_all( + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS), +}; + diff --git a/keyboards/wilba_tech/wt75_c/keymaps/via/rules.mk b/keyboards/wilba_tech/wt75_c/keymaps/via/rules.mk new file mode 100644 index 00000000..8834bf0c --- /dev/null +++ b/keyboards/wilba_tech/wt75_c/keymaps/via/rules.mk @@ -0,0 +1,2 @@ +RAW_ENABLE = yes +DYNAMIC_KEYMAP_ENABLE = yes \ No newline at end of file diff --git a/keyboards/wilba_tech/wt80_a/keymaps/via/rules.mk b/keyboards/wilba_tech/wt80_a/keymaps/via/rules.mk index 76a07d7a..8834bf0c 100644 --- a/keyboards/wilba_tech/wt80_a/keymaps/via/rules.mk +++ b/keyboards/wilba_tech/wt80_a/keymaps/via/rules.mk @@ -1,71 +1,2 @@ -# project specific files -SRC = drivers/issi/is31fl3736.c \ - drivers/avr/i2c_master.c \ - keyboards/wilba_tech/wt_mono_backlight.c \ - keyboards/wilba_tech/wt_main.c - -# MCU name -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section -BOOTLOADER = atmel-dfu - - -# Build Options -# change yes to no to disable -# -BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE = no # Mouse keys(+4700) -EXTRAKEY_ENABLE = yes # Audio control and System control(+450) -CONSOLE_ENABLE = no # Console for debug(+400) -COMMAND_ENABLE = no # Commands for debug and configuration -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend -# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -NKRO_ENABLE = yes # USB Nkey Rollover -BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality on B7 by default -MIDI_ENABLE = no # MIDI support (+2400 to 4200, depending on config) -UNICODE_ENABLE = no # Unicode -BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID -AUDIO_ENABLE = no # Audio output on port C6 -FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches - RAW_ENABLE = yes DYNAMIC_KEYMAP_ENABLE = yes \ No newline at end of file